How To Turn Off Audi Lane Assist

Windscreen: Camera window for Audi lane help

– Printing the button ⇒ fig. 158 -arrow- to switch the system on and off. The indicator lamp in the instrument cluster will calorie-free up or go out.

Indicator lamp in instrument cluster

Active: The green indicator lamp confirms that the organisation is fully functional. You will be warned if you are about to cross the lane markings detected by the system.

Inactive: The yellow warning lamp indicates that the system is switched on. However, you will non be warned if you cross the lane markings. This can have the post-obit causes:

• • In that location is but one or no lane marking.
• • The system cannot detect the lane markings (e.m. due to snow, dirt, wet conditions or adverse light).
• • At that place are more than two lane markings in the lane you are driving in (due east.thousand. in roadwork sections).
• • The vehicle's speed is below 65 km/h, the speed at which the lane assist system is activated.
• • The lane is narrower than two.5 m or wider than 5 m.
• • The curve is too tight.

Annotation

• • Make certain that the camera window, fig. 159 is not covered with stickers or similar objects.
• • Always continue the photographic camera window clean. Usually it should suffice to operate the windscreen wipers.

Instrument cluster brandish

Instrument cluster: lane assist switched on and in warning mode

Instrument cluster: lane assist switched on but not ready for warning

Yous can call up the display for the lane assist by repeatedly pressing the RESET push button on the windscreen wiper lever. For more details refer to.

When the lane assist is switched on, two lines bespeak the lane demarcations on the left and right of your vehicle.

Version A: Monochrome display

• • Solid red lines: The lane assist is switched on and ready to warn.
• • One scarlet line flashing (left or right): The lane assist warns you before you cross the lane demarcation ⇒ fig. 160, A
• • Unfilled lines: The lane assist is switched on but not ready for warning ⇒ page 146, fig. 161, A Version B: Loftier-resolution brandish
• • Solid white lines: The lane assistance is switched on and ready to warn.
• • Solid carmine line (left or right): The lane assist warns you before y'all cross the lane demarcation, fig. 160.
• • Unfilled lines: The lane assistance is switched on but not gear up for warning ⇒ folio 146, fig. 161.

Letters in the musical instrument cluster display

Should the lane aid be deactivated automatically, the indicator lamp in the instrument cluster will go out and one of the post-obit letters will appear in the instrument cluster display:

Audi lane assist non bachelor: currently no sensor vision

This bulletin is displayed when the camera is no longer functional later the system has continuously failed to detect the lane markings. This tin can take the following causes:

• • The outside of the camera window, fig. 159 is dirty or frosted. Please remove clay or ice from this area of the windscreen.
• • The inside of the camera window is misted up. In this case, please wait for the camera window to demist earlier switching on the lane assist system over again.
• • Due to the conditions (eastward.g. snow-covered road) the system has not been able to detect the lane markings for a long period. Practice not switch the lane help system on again before the lane markings are discernible.

Audi lane assist currently not available

A temporary mistake is preventing the lane assist system from fully functioning. Try switching on the lane assist system again later.

Audi lane assist: system fault

The organisation should be checked past an Audi dealership or other qualified workshop.

Setting the alarm fourth dimension and steering vibration

You tin can change the lane assistance settings on the audio system or MMI* to conform your private preferences.

Display: Setting fourth dimension of warning and steering vibration

– Select: Function selector button CAR > Audi lane assist.

Setting time of alarm

early: In this setting, the driver will be warned before a wheel crosses a lane mark. The warning depends on the bending with which the vehicle is budgeted the lane marking. The larger the angle with which you lot are driving towards the marking, the before y'all will receive the warning, i.e. the distance betwixt the vehicle and the marking might still be still relatively long. If you are driving toward the marking at a very narrow angle, you lot will receive the alert after, i.e. soon before i of the wheels touches the mark.

adaptive: In this setting, the time of warning is adapted to the road layout and the vehicle's speed. The alarm will be received later when you are driving through a bend, and earlier when you are driving on a directly section. On narrow roads, the system will give off warnings later on than on broad roads.

tardily: In this setting, the driver will be warned when a wheel crosses a lane marking.

Setting steering bicycle vibration

You tin fix the steering vibration to low, medium or potent. The steering wheel will vibrate so that y'all can check your pick.

Note

• • The lane assist is not agile while you lot are changing the setting; the brief vibration of the steering wheel is only intended to help you lot make the desired setting.
• • Your personal settings are stored automatically and assigned to the remote control cardinal which is beingness used.

Source: https://www.audihelp.com/auda-61-audi_lane_assist.html

Share this post